Cleaning Methods To Keep Your Bong Looking New
A filthy bong might ruin your smoking experience. Resin accumulation occurs when your bong is not consistently maintained and cleaned. Your bong eventually becomes blocked with bacteria, ash, tar, and filthy bong water, which results in foul-smelling smoke. It can be simple to ignore the warning signs, but if you can no longer taste the flavour of the premium cannabis you brought home, you are aware that your bong needs severe cleaning right now.
You should follow the recommendations for cleaning your bong provided below to keep it looking brand-new!
Basic Cleaning
Can you eat from a soiled, mold-covered plate? If the answer is an unequivocal no, then why would you want to smoke from a filthy, repulsive bong? Bongs are known for getting filthy and smelly quickly. They can quickly ruin the quality of your cannabis and make you sick if you're not careful. Fortunately, there is a quick and simple method to clean your bong: basic cleaning.
Just take your materials—coarse salt, baking soda, vinegar, and alcohol—and head to a spotless sink or basin with lots of water.
Wear your latex gloves and empty the remaining contents in your bong; Eliminate all herb leftovers from your bowl and ensure there's no water in the chamber.
Rinse the bong in warm water to loosen and get rid of any stubborn solids
Add some warm water partly into the bong. Note that extremely hot water can shatter and ruin your glass piece.
Carefully disassemble the parts of your bong to allow for a thorough clean up of each piece. Remove the bowl, pipe, and mouthpiece while inspecting any cracks or chips on the pieces that may need to be replaced.
Carefully put your pieces in a container, and add an abrasive (coarse salt) to tackle all the grime and stains and rubbing alcohol to clean the insides. Stronger rubbing alcohol (above 90%) will give you the best results.
Cover the holes with your hands and fingers to prevent spillages. Shake the bong thoroughly for a few minutes to remove all the buildup of resin, grime, and dirt.
Once you are content that you have done enough shaking for the best possible results, it's now time to empty all the dirty solution into the sink.
The next step is to rinse out your pieces thoroughly with clean water and repeat as many times as you need. Rinsing twice usually leaves your bong spic and span clean and looking as new as when you first bought it.
Eliminate All Stubborn Stains
This technique is especially helpful if your bong hasn't been cleaned in a while. Stains and dirt will adhere to difficult-to-reach spots. As a result, you should disassemble your bong and immerse it in warm water in a sink or other container. Pour a tiny amount of laundry detergent into the bong; a large amount will be difficult to rinse out completely and could leave a residual foul taste.
Allow the bong to soak for 60 minutes or more and then clean it as follows:
Add about a tablespoon of coarse salt into a sealable plastic bag (you can use two bags). Put enough rubbing alcohol (isopropyl )into the bag and soak all the small pieces of your bong. Ensure they are completely submerged before shaking the bag carefully for a few seconds. Allow the pieces to soak for a few minutes, then rinse each part thoroughly with clean water.
Scrub all the nooks and crannies of your pieces using a plastic cotton swab or an appropriate pipe cleaner.
Ensure all the stubborn stains and resin are eliminated by dipping the pieces in more rubbing alcohol and then scrubbing them out.
To remove the water stains in your bong, add some warm water and lemon juice to the chamber and swish it to reach every corner.
Finally, rinse out your bong thoroughly with cold, clean water.
Note: Please be aware that if you are using various abrasives and cleansers, the cleaning procedure to use is the same. However, depending on what you have on hand, you'll use rice, baking soda, or vinegar in place of coarse salt and isopropyl alcohol. These techniques are typically very cost-efficient, easy to use, and extremely effective. Each, however, has particular advantages and disadvantages. It's also important to remember that isopropyl alcohol and coarse salt produce the best outcomes!
Hot Water Method
You could think that cleaning your bong is a difficult process that you'd rather avoid. Of sure, it is in a certain sense. To begin an activity, you frequently need to find some motivation. But you can't take a chance by puffing from a filthy bong. Use this technique, at the very least, to deter tar, resin, mould, biofilm, and microbes.
For those who would prefer to avoid utilizing potent bong-cleaning chemicals, this method is also excellent. It is both natural and secure. A cold bong may shatter if you put boiling water in it.
Disassemble the smaller pieces and stems of your bong. Carefully gather them into a plastic container and add enough hot water to submerge every piece. Secure the airtight lid and leave the parts to soak.
Add enough water to fill the bong to the brim and secure all openings with duct tape or any heat-resistant wrap. Note that the glass will get very hot, and it might burn your hands. Therefore, protect wear oven mitts before shaking the bong thoroughly to clean all corners.
Use warm water to rinse the glass pieces and repeat. Do not use cold water as the temperature shock can shatter it!
Though this method may not be effective for an especially dirty bong with heavy residue and stain buildup, it is ideal for those who regularly clean their bongs
Commercial Bong Cleaning Products
Nothing is more frustrating than a bong that is filthy or blocked! To get stoned or high, you might never smoke enough tobacco! Additionally, you won't be able to taste your wonderful cannabis. But relax my darling stoner. You may clean your bong and avoid future resin and grime buildups by using any of a wide range of cleaning supplies. Great, isn't that right?
These items are designed exclusively to clean and maintain the usability of your stunning bong. Even better, the majority of these items are created from natural, plant-based materials, making them safe and non-toxic. No matter what kind of bong you use—glass, plastic, ceramic, metal, or even bamboo—there is always a product out there. The most important thing is to find the one that works best for your bong.
Empty the contents in your bong and rinse it out well with warm water.
Disassemble the pieces of your bong and put them into a plastic container.
Squirt an adequate amount of the cleaning detergent and hot water into the container.
Seal tightly and leave the pieces to soak overnight.
Always rinse thoroughly and allow your piece to dry before use
Taking Care of Your Bong
To take good care of and maintain your bong, you don't need to be an expert. Keep your glass piece clean and in good condition, if you want to get the greatest performance out of it. You can probably only do this to improve the flavour of your marijuana and maintain your health.
Remember this, a clean bong is a happy bong, and a happy bong will get you perfectly stoned! Here's how to take care of your bong:
Only use filtered water in your bong. This avoids stains and discoloration of your glass piece.
Change your bong water every day to prevent biofilm and mold formation.
At least clean your bong thoroughly every once a week to eliminate any stains
Always secure your bong in its bag or a rigid casing to avoid cracking or breaking.
Consider using soft brushes to get rid of resin and dirt out of the 'hidden' places.
Key Take-Aways
Your bong will be simpler to clean if you keep it in good condition. In order to counteract biofilms and prevent hard water stains, you must frequently change the water in your bong. It takes work to keep your bong clean, especially if you smoke frequently. But using any of the aforementioned bong cleaning techniques, you'll find the procedure pleasurable and simple!
